[Free] 2018(Aug) Dumps4cert Cisco 500-290 Dumps with VCE and PDF Download 81-90

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 Aug Cisco Official New Released 500-290
100% Free Download! 100% Pass Guaranteed!

Implementing Cisco IP Switched Networks

Question No: 81

What condition was match during etherchannel configuration.

  1. Spanning tree port priority

  2. Spanning tree cost

  3. Interface Description

  4. Trunk mode

  5. Trunk allow vlan

Answer: D,E

Question No: 82

Which statement about the use of PAgP link aggregation on a Cisco switch that is running Cisco IOS Software is true?

  1. PAgP modes are off, auto, desirable, and on. Only the combinations auto- desirable,desirable-desirable, and on-on allow the formation of a channel.

  2. PAgP modes are active, desirable, and on. Only the combinations active-desirable,

    desirable-desirable, and on-on allow the formation of a channel.

  3. PAgP modes are active, desirable, andon. Only the combinations active-active, desirable-desirable, and on-on allow the formation of a channel.

  4. PAgP modes are off, active, desirable, and on. Only the combinations auto-auto, desirable-desirable, and on-on allow the formation of a channel.

Answer: A

Question No: 83

Behavior of an access port when a tagged packet is received other than the access VLAN value.

  1. Tag is removed and packet is forwarded of the VLAN mentioned in the tag.

  2. tag is removed and packet is forwarded on the VLAN of the access port

  3. Not Available

  4. packet is dropped

Answer: D

Question No: 84

Youhave been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

You are adding new VLANs. VLAN500 and VLAN600 to thetopology in such way that you need to configure SW1 as primary root for VLAN 500 and secondary for VLAN 600 and SW2 as primary root for VLAN 600 and secondary for VLAN 500. Which configuration step is valid?

  1. Configure VLAN 500 amp; VLAN 600 on both SW1 amp;SW2

  2. Configure VLAN 500 and VLAN 600 on SW1 only

  3. Configure VLAN 500 and VLAN 600 on SW2 only

  4. Configure VLAN 500 and VLAN 600 on SW1 ,SW2 and SW4

  5. On SW2; configure vtp mode as off and configure VLAN 500 and VLAN 600; configure back to vtp server mode.

Answer: A Explanation:

By issuing the 鈥渟how vtp status command on SW2, SW2, and SW4 we see that both SW1 and SW2 are operating in VTP server mode, but SW4 is a client, so we will need to add both VLANs to SW1 and SW2.

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

Question No: 85

Which option lists the information that is contained in a Cisco Discovery Protocol advertisement?

  1. native VLAN IDs, port-duplex, hardware platform

  2. native VLANIDs, port-duplex, memory errors

  3. native VLAN IDs, memory errors, hardware platform

  4. port-duplex, hardware platform, memory errors

Answer: A

Question No: 86

It a switch stack is configured to used SDM templates, where are the templates stored?

  1. stack master

  2. TFTP server

  3. flash memory

  4. all stack members

Answer: A

Question No: 87

Which switch is chosen as the stack master during a stack master election orre-election?

  1. the switch with the highest stack member ID

  2. the switch with the lowest stack member ID

  3. the switch with the lowest stack member priority value

  4. the switch with the highest stack member priority value

Answer: D

Question No: 88

Refer to the exhibit.

Dumps4Cert 2018 PDF and VCE

DSW1 should share the same MST region with switch DSW2. Which statement is true?

  1. Configure DSW1 with the sameversion number, and VLAN-to-instance mapping as shown on DSW2.

  2. DSW2 uses the VTP server mode to automatically propagate the MST configuration to DSW1.

  3. DSW1 automatically inherits MST configuration from DSW2 because they have the same domain name.

  4. Configure DSW1 with the same region name, revision number, and VLAN-to-instance mapping as shown on DSW2.

  5. DSW1 is in VTP client mode with a lower configuration revision number, therefore, it automatically inherits MST configuration from DW2.

Answer: D

Question No: 89

Which describes the default load balacing scheme used by the Gateway Load Balancing Protocol (GLBP)?

  1. Per host using a strict priority scheme

  2. Per session using a round-robin scheme

  3. Per session using a strict priority scheme

  4. Per GLBPgroup using a strict priority scheme

  5. Per host basis using a round robin-scheme

  6. Per GLBP group using a round-robin scheme

Answer: E

Question No: 90

Which two statements about CDP are true? (Choose two.)

  1. CDP uses a TLV to advertise the native VLAN

  2. CDP is not supported with SNMP

  3. CDP is supported on Frame Relay sub interfaces.

  4. CDP runs on OSI layer 2

  5. CDP runs on OSI layer 1

Answer: A,C

100% Dumps4cert Free Download!
500-290 PDF
100% Dumps4cert Pass Guaranteed!
500-290 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No