Implementing Cisco IP Telephony amp; Video, Part 2 v1.0
Question No: 171
Refer to the exhibit.
Which option describes the effect of this configuration?
It implements Cisco United CME redundancy.
It configures a standby Cisco Unified E.
It configures failover.
It implements Cisco IOS redundancy.
It creates dial peers.
It implements HSRP.
Question No: 172
There are two call control systems in this item.
The Cisco UCM is controlling the DX650, the Cisco Jabber for Windows Client, and the 7965 and 9971 Video IP Phones.
The Cisco VCS and TMS control the Cisco TelePresence Conductor, the Cisco TelePresence MCU, and the Cisco Jabber TelePresence for Windows.
The intercluster URI call routing no longer allows calls between sites. What is the reason
why this would happen?
Wrong SIP domain configured.
User is not associated with the device.
IP or DNS name resolution issue.
No SIP route patterns for cisco.lab exist.
Question No: 173
Refer to the exhibit.
How does the Cisco Unified Communications Manager advertise dn-block 2?
A. 14087071222 with number type international
B. 14087071222 with number type international
Question No: 174
You are the Cisco Unified Communications Manager in Certpaper.com. You use a remote site MGCP gateway to provide redundancy when connectivity to the central Cisco Unified Communications Manager cluster is lost. How to enable IP phones to establish calls to the PSTN when they have registered with the gateway? (Choose three.)
POTS dial peers must be added to the gateway to route calls from the IP phones to the PSTN.
The default service must be enabled globally.
The command ccm-manager mgcp-fallback must be configured.
COR needs to be configured to disallow outbound calls.
Explanation: Incorrect answer: D
Class of restriction: Cisco Unified Communications Manager Business Edition 3000 supports class of service (CoS) with respect to geographic reach as follows:
Speed dials: Single-button, not BLF Link:
Question No: 175
What happens if location-based CAC is used and there is no bandwidth available when a remote caller is placed on hold?
Cisco Unified Communications Manager sends TOH rather than MOH.
Cisco Unified Communications Manager terminates the call.
Cisco Unified Communications Manager plays default MOH.
Cisco Unified Communications Manager attempts to reconnect the call immediately.
Question No: 176
Which system configuration is used to set a restriction on audio bandwidth?
Question No: 177
In Cisco Unified Communications Manager, where do you configure the default bit rate for audio and video devices?
Region under Region Information
Cisco CallManager service under Service Parameter Configuration
Enterprise Phone Configuration
Question No: 178
An administrator is setting up analog phones that connect to a Cisco VG310. Which type of gateway or trunk on Cisco Unified Communication Manager for the Cisco VG310 must the administrator set up to allow the phones to have the call pickup feature?
B. 323 gateway
E. 225 trunk
Reference: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/9_1_1/ccmsys/CUCM_ BK_C55
65591_00_cucm-system-guide-91/CUCM_BK_C5565591_00_cucm-system-guide- 91_chapter_0100111.html (see table 1)
Question No: 179
The network administrator has been investigating bandwidth issues between the central office and remote sites where location-based CAC is implemented. What does the Cisco Unified Communications Manager quot;LocationOutOfResourcesquot; counter indicate?
This counter represents the total number of times that a call on a particular Cisco Unified Communications Manager through the location failed due to lack of bandwidth.
This counter represents the total number of times that a call through locations failed due to the lack of bandwidth.
This counter represents the total number of failed video-stream requests (most likely due to lack of bandwidth) in the location where the person who initiated the video conference resides.
This counter represents the total number of times since the last restart of the Cisco IP Voice Streaming Application that a Cisco Unified Communications Manager connection was lost.
Question No: 180
When an incoming PSTN call arrives at an H.323 gateway, how does the called number get normalized to an internal directory number in Cisco Unified Communications Manager?
Normalization is done by configuring the significant digits for inbound calls on the H.323 gateway configuration in Cisco Unified Communications Manager.
Normalization is done using route patterns.
Normalization is done using the gateway incoming calling party prefixes based on number type.
Normalization is achieved by local route group that is assigned to the H.323 gateway.
|Lowest Price Guarantee||Yes||No||No|
|Free VCE Simulator||Yes||No||No|