[Free] 2018(Aug) Ensurepass Cisco 300-080 Dumps with VCE and PDF 91-100

Ensurepass.com : Ensure you pass the IT Exams
2018 Aug Cisco Official New Released 300-080
100% Free Download! 100% Pass Guaranteed!

Troubleshooting Cisco IP Telephony amp; Video v1.0

Question No: 91

Which two components can be software upgraded via Cisco TelePresence Management Suite? (Choose two.)

  1. unmanaged endpoints

  2. endpoints that are managed by Cisco TelePresence Management Suite

  3. endpoints that are provisioned by Cisco TelePresence Management Provisioning Extension

  4. endpoints that are registered by Cisco Unified Communications Manager

  5. endpoints that are registered by a partner company

Answer: B,C

Question No: 92

Refer to topology and Exhibits below:

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

After making a change to a manually configured MGCP gateway, what step should you take to ensure that the gateway accepts the changes and be operational?

  1. Issue the commands no MGCP, then MGCP.

  2. Issue the commands no SCCP, then SCCP.

  3. Issue the commands Shut, then no shut.

  4. Issue the commands no CCM, then CCM.

Answer: A

Question No: 93

Endpoints are configured for both H.323 and SIP using the same URI and Cisco VCS settings, but the endpoints register only as H.323 endpoints. What is causing this issue?

  1. A firewall is blocking all traffic from the endpoints to the Cisco VCS.

  2. The Cisco VCS has no SIP domains configured.

  3. The Cisco VCS is blocking the endpoints because of duplicate ID entries.

  4. The endpoints do not have the SIP option key installed.

  5. SIP does not work, because SIP is used for Cisco Unified Communications Manager registration only.

Answer: B

Question No: 94

Cisco Unified Mobile Connect has been enabled, but users are not able to switch an in- progress call from their mobile phone to their desk phone. You find out that the Resume softkey option does not appear on the desk phone after users hang up the call on their mobile phone. What do you do to resolve this issue?

  1. Issue the progress_ind progress disable command in the gateway.

  2. Issue the voice call disc-pi-off command in the gateway.

  3. Enable mobile connect on the user profile.

  4. Assign Resume softkey on the desk phone.

Answer: B

Question No: 95

Cisco Unified Communications Manager is deployed in a head office and also provides telephony services to remote regional offices. What is a possible cause of call setup issues with phones in the regional offices?

  1. remote office firmware for phones

  2. codec mismatch in region information settings

  3. end user roles and groups

  4. physical location configuration

Answer: B

Question No: 96

Refer to the exhibits.

Ensurepass 2018 PDF and VCE

Assume that all learned SAF routes are placed in the SAF_Pt partition. The 3XXX directory number pattern is being advertised by a remote cluster and is also being blocked by the local cluster that is shown in the exhibit. An IP phone is attached to the local cluster and is configured with a CSS that contains the following partitions: SAF_Pt and Internal_Pt in this order. When the IP phone places a call to 3001, what will occur?

  1. The call will succeed and will be placed via the SIP_Trunk.

  2. The call will fail because it will be blocked by the CCD Blocked Learned Route configuration.

  3. The call will be placed in a round-robin fashion between the SAF network and SIP_Trunk.

  4. The call will placed in a round-robin fashion between the SAF network and SIP_Trunk. Every other call will fail.

Answer: A

Question No: 97

You configured a Cisco ISR G2 as a SIP gateway, but the gateway does not show that it is registered with Cisco Unified Communications Manager. What is causing this issue?

  1. Cisco Unified Communications Manager does not support SIP gateways.

  2. The gateway does not have the UC license installed.

  3. The gateway does not have Cisco Unified Border Element session licensing.

  4. Cisco Unified Communications Manager does not show a SIP gateway as registered if it is not properly configured.

  5. Cisco Unified Communications Manager never shows a SIP gateway as registered even when it is properly configured.

  6. The Cisco ISR G2 cannot be a SIP gateway.

Answer: E

Question No: 98

To achieve 720p (HD) quality at 30 frames per second on an endpoint that is running TC software, what is the minimum configured call rate?

  1. 512 kbps

  2. 1152 kbps

  3. 768 kbps

  4. 2560 kbps

Answer: B

Question No: 99

When dialing any external SIP URI for a business-to-business call, an endpoint that is registered to the Cisco VCS Control fails to locate the remote endpoint. The same endpoint can successfully call another endpoint that is registered to the Cisco VCS Expressway.

How do you resolve this issue?

  1. Add traversal call licensing on the Cisco VCS Expressway.

  2. Add traversal call licensing on the Cisco VCS Control.

  3. Add a multisite option to the endpoint.

  4. Configure a proper DNS zone on the Cisco VCS Expressway.

  5. Configure a traversal zone between the Cisco VCS Control and the Cisco VCS Expressway.

  6. Configure a SIP route pattern in Cisco Unified Communications Manager.

Answer: D

Question No: 100

What is the default interval for SAF hello packets?

  1. 15 seconds

  2. 15 seconds on links with speeds that are slower than T1 speeds

  3. 40 seconds

  4. 40 seconds on links with speeds that are slower than T1 speeds

  5. 60 seconds

  6. 60 seconds on links with speeds that are slower than T1 speeds

Answer: F

100% Ensurepass Free Download!
300-080 PDF
100% Ensurepass Free Guaranteed!
300-080 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No