[Free] 2019(Nov) EnsurePass Cisco 200-125 Dumps with VCE and PDF 91-100

Get Full Version of the Exam

Question No.91

Which command shows your active Telnet connections?

  1. show cdp neigbors

  2. show session

  3. show users

  4. show vty logins

Correct Answer: B


The quot;show usersquot; shows telnet/ssh connections to your router while quot;show sessionsquot; shows telnet/ssh connections from your router (to other devices). The question asks about quot;your active Telnet connectionsquot;, meaning connections from your router so the answer should be B.

Question No.92

Which command reveals the last method used to powercycle a router?

  1. show reload

  2. show boot

  3. show running-config

  4. show version

Correct Answer: D


The quot;show versionquot; command can be used to show the last method to powercycle (reset) a router.


Question No.93

Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?


  1. AS numbers must be changed to match on all the routers

  2. Loopback interfaces must be configured so a DR is elected

  3. The no auto-summary command is needed on Router A and Router C

  4. Router B needs to have two network statements, one for each connected network

Correct Answer: A


This question is to examine the understanding of the interaction between EIGRP routers. The following information must be matched so as to create neighborhood. EIGRP routers to establish, must match the following information:

  1. AS Number;

  2. K value.

Question No.94

Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.)

Router(config)# router ospf 1

  1. All OSPF routers in an area must have the same process ID.

  2. Only one process number can be used on the same router.

  3. Different process identifiers can be used to run multiple OSPF processes

  4. The process number can be any number from 1 to 65,535.

  5. Hello packets are sent to each neighbor to determine the processor identifier.

Correct Answer: CD


Multiple OSPF processes can be configured on a router using multiple process ID#39;s. The valid process ID#39;s are shown below:

Edge-B(config)#router ospf ?

lt;1-65535gt; Process ID

Question No.95

Which two locations can be configured as a source for the IOS image in the boot system command? (Choose two.)

  1. RAM

  2. NVRAM

  3. flash memory

  4. HTTP server

  5. TFTP server

  6. Telnet server

Correct Answer: CE


The following locations can be configured as a source for the IOS image:

1. Flash (the default location)

2. TFTP server

3. ROM (used if no other source is found)

Question No.96

Refer to the exhibit. The Lakeside Company has the internetwork in the exhibit. The administrator would like to reduce the size of the routing table on the Central router. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?


  1. is subnetted, 1 subnets

    D [90/20514560] via, 6w0d, Serial0/1

  2. is subnetted, 1 subnets

    D [90/20514560] via, 6w0d, Serial0/1

  3. is subnetted, 1 subnets

    D [90/20514560] via, 6w0d, Serial0/1

  4. is subnetted, 1 subnets

    D [90/20514560] via, 6w0d, Serial0/1

  5. is subnetted, 1 subnets

    D [90/20514560] via, 6w0d, Serial0/1

  6. is subnetted, 1 subnets

D [90/20514560] via, 6w0d, Serial0/1

Correct Answer: D


The route includes,, and networks only.

Question No.97

Which type of EIGRP route entry describes a feasible successor?

  1. a backup route, stored in the routing table

  2. a primary route, stored in the routing table

  3. a backup route, stored in the topology table

  4. a primary route, stored in the topology table

Correct Answer: C


EIGRP uses the Neighbor Table to list adjacent routers. The Topology Table list all the learned routers to destination whilst the Routing Table contains the best route to a destination, which is known as the Successor. The Feasible Successor is a backup route to a destination which is kept in the Topology Table.

Question No.98

Which two statements about the OSPF Router ID are true? (Choose two.)

  1. It identifies the source of a Type 1 LSA.

  2. It should be the same on all routers in an OSPF routing instance.

  3. By default, the lowest IP address on the router becomes the OSPF Router ID.

  4. The router automatically chooses the IP address of a loopback as the OSPF Router ID.

  5. It is created using the MAC Address of the loopback interface.

Correct Answer: AD Explanation: r120#show ip ospf data

OSPF Router with ID ( (Process ID 1) Next, who are the other routers in our area?

Router Link States (Area 1)

Link IDADV RouterAgeSeq#ChecksumLink count 0x0092B31×80000234 0x009CAC1

We can see OSPF Router ID will be used as source of Type 1 LSA. Also the router will chose the highest loopback interface as its OSPF router ID (if available).

Question No.99

What is a global command?

  1. a command that is set once and affects the entire router

  2. a command that is implemented in all foreign and domestic IOS versions

  3. a command that is universal in application and supports all protocols

  4. a command that is available in every release of IOS, regardless of the version or deployment status

  5. a command that can be entered in any configuration mode

Correct Answer: A


When you enter global configuration mode and enter a command, it is applied to the running configuration file that is currently running in ram. The configuration of a global command affects the entire router. An example of a global command is one used for the hostname of the router.

Question No.100

Refer to the exhibit. C-router is to be used as a quot;router-on-a-stickquot; to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?


  1. These commands need to be added to the configuration: C-router(config)# router eigrp 123

    C-router(config-router)# network172.19.0.0

  2. These commands need to be added to the configuration: C-router(config)# router ospf 1

    C-router(config-router)# network area 0

  3. These commands need to be added to the configuration: C-router(config)# router rip

    C-router(config-router)# network172.19.0.0

  4. No further routing configuration is required.

Correct Answer: D


Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLA will be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols need to be configured.

Get Full Version of the Exam
200-125 Dumps
200-125 VCE and PDF