[Free] 2019(Nov) EnsurePass Cisco 300-160 Dumps with VCE and PDF 1-10

Get Full Version of the Exam
http://www.EnsurePass.com/300-160.html

Question No.1

Which two options are advantages when using NPIV? (Choose two.)

  1. allows a single physical N-Port to have single WWPNs, and therefore single N-Port IDs, associated with it

  2. NPIV-enabled physical N-Port can subsequently issue additional commands to register more WWPNs and receive more N-Port IDs (one for each WWPN).

  3. allows a #39;single#39; physical N-Port to have multiple WWPNs, and therefore multiple N-Port IDs, associated with it

  4. NPV-enabled physical N-Port can subsequently issue additional commands to register more WWPNs and receive more N-Port IDs (one for each WWPN).

  5. allows #39;multiple#39; single physical N-Port to have multiple WWPNs, and therefore multiple N-Port IDs, associated with it

  6. N-Port on the physical host would have only a single WWPN (and N-Port ID).

Correct Answer: BC

Question No.2

Which component is required to run FCoE?

  1. converged network adapter

  2. iSCSI gateway

  3. host bus adapter

  4. Fibre Channel adapter

Correct Answer: A

Explanation:

Computers can connect to FCoE with converged network adapters (CNAs), which contain both Fibre Channel host bus adapter (HBA) and Ethernet Network Interface Card (NIC) functionality on the same adapter card. CNAs have one or more physical Ethernet ports. FCoE encapsulation can be done in software with a conventional Ethernet network interface card, however FCoE CNAs offload (from the CPU) the low level frame processing and SCSI protocol functions traditionally performed by Fibre Channel host bus adapters.

Question No.3

You have a Cisco UCS B-Series chassis. To connect to a blade server by using a remote KVM console, you should connect to the IP address of which component?

  1. mgmt0

  2. CIMC

  3. IPMI

  4. CMP

Correct Answer: B

Question No.4

Which two Nexus 7000 licenses are required to manage FabricPath from Cisco Data Center Network Manager (DCNM)? (Choose two.)

  1. Nexus 7000 Enhanced Layer 2 License

  2. Nexus 7000 Transport Services License

  3. Cisco DCNM for SAN Advanced Edition for Nexus 7000

  4. Nexus 7000 LAN Enterprise License

  5. Cisco DCNM for Nexus 7000

  6. Nexus 7000 Scalable Feature License

Correct Answer: AE

Question No.5

When you configure FCIP, which two types of acceleration can you enable to maximize WAN link utilization? (Choose two)

  1. SCSI write

  2. link

  3. SCSI tape

  4. WAN

  5. IP

Correct Answer: AC

Explanation: http://www.cisco.com/en/US/products/ps5989/products_configuration_guide_chapter09186a0080 664e20.html

Question No.6

Which two options are reasons to use Layer 3 routing to segment a data center instead of Layer 2 switching? (Choose two)

  1. limit the scope of Spanning Tree Protocol

  2. simplify design

  3. ease of routing protocol configuration

  4. limit the scope of broadcast flooding

  5. cost

Correct Answer: CD

Question No.7

You have a Cisco UCS Fabric Interconnect that connects to upstream switches via four 10-Gbps port channels. You have a fully populated Cisco UCS B-Series Blade Server chassis that has a UCS-IOM 2208XP installed and uses all of the ports for the blade servers. What is the oversubscription ratio between the chassis and the upstream switch?

A. 6:1

B. 3:1

C. 2:1

D. 4:1

Correct Answer: B

Question No.8

Which option accurately describes the OSPF Graceful Restart feature in Cisco NX-OS?

  1. keeps the control plane state active during an OSPF process restart

  2. shuts down the OSPF process gracefully to replace the router

  3. prevents the OSPF process from restarting when the process crashes

  4. allows a router to remain in the data forwarding path during an OSPF process restart

Correct Answer: D

Explanation:

A graceful restart, or nonstop forwarding (NSF), allows OSPFv2 to remain in the data forwarding path through a process restart. When OSPFv2 needs to perform a graceful restart, it sends a link- local opaque (type 9) LSA, called a grace LSA. http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_2/nx- os/unicast/configuration/guide/l3_cli_nxos/l3_ospf.html#52215

Question No.9

The classical aggregation layer design does not provide isolation on the control plane and on the data plane. What is the solution to this problem?

  1. STP

  2. VDC

  3. Cisco ISO ISSU

  4. HSRP

Correct Answer: B

Question No.10

You deploy new server infrastructure by using a Cisco UCS platform. Winch two design options can you use to increase the redundancy of the new compute solution#39; (Choose two.)

  1. a 10-Gb uplink port

  2. a pin vNic in the server profile to a specific Fabric Interconnect node that has failover disabled

  3. adding multiple ports to uplink port channels

  4. static pinning at the server ports

  5. more than one server port to connect the Cisco UCS B-Series blade IOM

Correct Answer: BC

Get Full Version of the Exam
300-160 Dumps
300-160 VCE and PDF