[Free] 2019(Nov) EnsurePass Juniper JN0-102 Dumps with VCE and PDF 321-330

November 4, 2019

JN0-102 Dumps 2019-11

, , , , , ,

Get Full Version of the Exam
http://www.EnsurePass.com/JN0-102.html

Question No.321

Which two statements are correct about the request system zeroize local command? (Choose two.)

  1. The command preserves the management interface addresses.

  2. The command resets all key values.

  3. The command removes all data files.

  4. The command removes all user-created files from the system.

Correct Answer: BD

Question No.322

You have configured logging to the console port but are uncertain of the impact to the device while troubleshooting. In this scenario, which command would allow you to minimize the impact?

  1. commit synchronize comment troubleshoot

  2. commit confirmed 1 comment troubleshoot

  3. set system syslog console any none

  4. set system syslog log-rotate-frequency 15

Correct Answer: C

Question No.323

Which two statements about subnet masks are true? (Choose two.)

  1. If a bit is turned on (1), the corresponding bit in the IP address is used for the host portion.

  2. If a bit is turned off (0), the corresponding bit in the IP address is used for the host portion.

  3. If a bit is turned on (1), the corresponding bit in the IP address is used for the network prefix.

  4. If a bit is turned off (0), the corresponding bit in the IP address is used for the network prefix.

Correct Answer: BC

Question No.324

Which command causes the Junos OS temporarily activate a configuration?

  1. commit and-quite

  2. commit synchronize

  3. commit check

  4. commit confirmed

Correct Answer: D

Question No.325

In Ethernet networks, duplex mismatches will lower performance. Which error statistics can be seen if a duplex mismatch is present?

  1. collisions on the full-duplex side; runts on the half-duplex side

  2. collisions on the full-duplex side; collisions on the half-duplex side

  3. collisions on the half-duplex side; framing errors on the full-duplex side

  4. collisions on the half-duplex side; giants on the full-duplex side

Correct Answer: C

Explanation:

On an Ethernet connection, a duplex mismatch is a condition where two connected devices operate in different duplex modes, that is, one operates in half duplex while the other one operates in full duplex.

This results in the full-duplex side receiving an incomplete frame with CRC error or a runt frame. It does not detect any collision since CSMA/CD is disabled on the full-duplex side. As a result, when both devices are attempting to transmit at (nearly) the same time, the packet sent by the fullduplex end will be discarded and lost due to an assumed collision and the packet sent by the half duplex device will be delayed or lost due to a CRC error in the frame.

References: https://en.wikipedia.org/wiki/Duplex_mismatch

Question No.326

What is the default firewall filter behavior when a term is matched but no terminating action is specified?

  1. an implicit deny and the filter evaluation terminates

  2. an implicit accept and the filter evaluation terminates

  3. an implicit accept and the filter evaluation continues to the next term

  4. an implicit deny and the filter evaluation continues to the next term

Correct Answer: C

Question No.327

What is correct regarding the configuration shown below?

static route 0.0.0.0/0 qualified-next-hop 172.30.25.1 preference 7 next-hop 172.30.25.5

  1. The next-hop 172.30.25.1 is selected because the address has the lowest value.

  2. The next-hop 172.30.25.1 is selected because it is listed first.

  3. The next-hop 172.30.25.1 is selected because it is the lowest protocol preference.

  4. The next-hop 172.30.25.5 is selected because it is the lowest protocol preference.

    Correct Answer: D

    Explanation:

    The routes with a lower route preference are always used to route traffic. Preference 5 is the default preference for static routes.

    References: https://www.juniper.net/documentation/en_US/junos15.1/topics/concept/routingprotocol-static- security-route-preference-and-qualified-next-hop-understanding.html

    Question No.328

    What is the decimal equivalent of 00000100?

    A.

    2

    B.

    4

    C.

    9

    D.

    12

    Correct Answer: B

    Question No.329

    Which two options are reasons for using traffic classification? (Choose two.)

    1. to use the classification to route traffic

    2. to use the classification to reorder packets from various sources

    3. to use the classification to discard malformed packets

    4. to use the classification to provide the configured service level

Correct Answer: AD

Explanation:

Classification entails using a traffic descriptor to categorize a packet within a specific group to define that packet and make it accessible for QoS handling on the network. Using packet classification, you can partition network traffic into multiple priority levels or classes of service.

References: https://www.cisco.com/c/en/us/td/docs/ios/12_2/qos/configuration/guide/fqos_c/qcfclass.pdf

Question No.330

Which command will display the temperature of the Routing Engine#39;s CPU?

  1. show chassis environment

  2. show chassis routing-engine

  3. show chassis temperatures

  4. show chassis status

Correct Answer: B

Explanation:

The output fields for theshow chassis routing-engine command include: Temperature: Temperature of the air flowing past the Routing Engine.

References: https://www.juniper.net/documentation/en_US/junos11.4/topics/reference/commandsummary/sho w-chassis-routing-engine.html

Get Full Version of the Exam
JN0-102 Dumps
JN0-102 VCE and PDF

Related Posts